Description:

Key Features

Drill Stays Put The Veto Pro Pac DH2 Large Drill Holster keeps your drill at your side instead of buried in a bag or balanced on a ladder. That means faster grabs, fewer drops, and less wasted motion during repetitive fastening work. Extra Bit Storage Six exterior pockets plus four 1-inch bit holders give you dedicated space for bits, extensions, and nut drivers. You keep the common stuff right where you need it instead of digging through a pouch. Built for Jobsite Wear Nylon construction with aluminum hardware gives this holster the kind of rugged build that makes sense for daily belt carry. It is made to handle regular jobsite use without feeling flimsy.

Overview

Veto Pro Pac DH2 Large Drill Holster is a large nylon drill holster built for carrying a drill and the small accessories that usually end up scattered across your belt or pocket. This is a drill holster designed for drill carry, bit storage, and faster access during fastening and installation work. Model number: DH2. If you work with a drill all day and want a dedicated place for it that also holds the basics, this setup makes a lot of sense.

The big selling point here is not just that it holds a drill. It is that the holster adds organization around the drill. The exterior sides include six small pockets sized for 2-inch to 4-inch bits, extensions, and nut drivers, and the top webbing strip gives you an easy spot for short driver tips. There is also a tape measure clip slot behind the front panel and a safety lanyard included. In real use, that means fewer trips back to the bag and less time hunting for the bit or driver you just had in your hand.

The layout is practical. The bottom flap closes to protect the chuck when you want a more contained carry, but it also opens for long bit clearance. That matters if you switch between compact driver setups and longer accessories during the same day. Instead of forcing one carry style, the DH2 gives you some flexibility without turning into a bulky pouch.

Build quality is straightforward and job-focused. The holster uses nylon as the primary material and aluminum hardware for added durability. At 6 inches wide, 11.5 inches high, and 3 inches deep, it is compact enough to ride on a belt without taking over your whole setup, but still sized as a large drill holder. The 1.0-pound weight keeps it substantial without being overbuilt for what it is supposed to do.

Mounting options are another strong point. The belt pass-through keeps the holster planted at your side while you work, and the product can also be attached to a tool bag. The rear vertical molle gives you another mounting path if you want to add Veto Pro Pac's stainless-steel repositionable belt clip, which is sold separately. That makes the DH2 useful for users who change between belt carry and bag-mounted organization depending on the job.

This drill holder is a good fit for general contractors, framers, HVAC techs, aviation technicians, installers, and carpenters who want their drill and go-to accessories in one place. Serious DIY users will appreciate it too, but this is especially useful for tradespeople who are constantly moving, climbing, measuring, and fastening. If your drill is one of the tools you reach for every few minutes, a dedicated holster like this earns its space fast.

Keep Your Drill Ready to Grab

This large drill holster is built to keep the tool you use most within easy reach. For installers and service trades, that means less bending down, less pocket clutter, and quicker transitions between drilling, driving, and measuring.

• Large holster design sized for drill carry
• Belt pass-through helps keep the holster riding at your side

Carry Bits Without Pocket Junk

The DH2 is more than a simple sleeve for a drill. The outside storage lets you keep the bits and drivers you actually use most often right on the holster, which is a lot more efficient than stuffing them into a general pouch.

• Six exterior pockets for bits, extensions, and nut drivers
• Four 1-inch bit holders plus a tape measure clip location

Adjust for Short or Long Accessories

The bottom flap is one of those small details that ends up mattering on the job. Close it when you want more protection around the chuck, or open it up when you need clearance for a longer bit so the holster does not fight the way you work.

• Bottom flap closes to protect the chuck
• Opens for long bit clearance when needed

What's in the Box

• (1) Veto Pro Pac DH2 Large Drill Holster

Drill, bits, tape measure, and optional repositionable belt clip are sold separately.

Key Specifications

Compatibility

Carry Options Can be attached as a belt pass-through to keep the holster at your side while working. Bag Mounting Can also be attached to a tool bag for users who want drill storage on their bag instead of on-belt carry. Rear Molle Vertical rear molle can be used with Veto Pro Pac's stainless-steel repositionable belt clip, sold separately.

Built For

General Contracting Framing HVAC Aviation Technicians Installers Carpentry Fastening Work DIY / Hobbyist

Pro Tip

If you run longer driver accessories, leave the bottom flap open so the tool seats naturally instead of hanging up on the bit. When you switch back to standard setups, close the flap to give the chuck a little more protection while you move around the site.

Warranty & Support

5-year limited warranty.

Tool Nut's Take

Tool Nut's Take

Veto Pro Pac DH2 Large Drill Holster Keeps the Essentials Together

This is the kind of holster that earns its keep when your drill is in and out of your hand all day.

• Who it's for: Contractors, installers, HVAC techs, framers, carpenters, and serious DIY users who want a dedicated spot for a drill plus the bits and drivers that go with it.
• Why it stands out: The extra storage is the real value here. You get drill carry, exterior bit organization, a tape measure clip point, and a bottom flap that adapts to short or long accessories.
• Worth knowing: This is a holster, not a loaded kit. The optional repositionable belt clip is sold separately, so if that mounting style matters to you, plan for it up front.

Common Questions

• What is the Veto Pro Pac DH2 Large Drill Holster made from? It uses nylon as the primary material and aluminum hardware.
• How many storage areas does it have? The product is listed with 8 compartments, and it also includes six exterior pockets plus four 1-inch bit holders for small accessory organization.
• Can it be worn on a belt? Yes. It has a belt pass-through so it can ride at your side while you work.
• Can it handle longer drill accessories? Yes. The bottom flap opens to provide clearance for longer bits.